newest embroidery hoops and accessories

Produce embroidered patches faster and more precisely.. This magnetic patch frame is based on the proven ZSK SPRINT Border Frame and adds a separate lower frame that holds a hook-and-loop backing plate measuring 470 × 320 mm. Embroider your emblems and designs into the tensioned fabric first, then add the patch backing in a single, repeatable workflow – ready for laser cutting. How it works Hoop the fabric. Tension your base fabric in the SPRINT border frame and embroider the emblems or designs as usual. Insert the hook-and-loop plate. Place a 470 × 320 mm hook-and-loop plate into the separate lower frame. Fix with magnets. The lower frame is held in position underneath the border frame by magnets – no tools, no screws, exact repeat positioning. Sew on the hook-and-loop. Stitch the hook-and-loop backing to the patches in the same run. Cut to shape. Send the finished patches straight to the laser cutter for clean, contour-accurate edges. /ol> Your advantages Two steps in one setup: Embroider the emblem and attach the hook-and-loop backing without re-hooping – fewer handling steps, higher throughput. Repeatable accuracy: Magnetic fixing locates the lower frame in exactly the same position every cycle, keeping embroidery, backing and laser contour perfectly aligned. Toolless changeover: Magnets replace clamps and screws – fast plate changes and minimal downtime between runs. Built for laser finishing: The hook-and-loop plate format of 470 × 320 mm is designed for an efficient embroider-and-cut process with clean laser-cut edges. Based on a proven system: Built on the established ZSK SPRINT Border Frame, so it integrates into your existing SPRINT workflow. Ideal for series production: Perfect for patches, emblems, name tags and branding elements in batch quantities. Application areas Patch and emblem manufacturing, workwear and uniform branding, sportswear, promotional and merchandising patches, and any application that combines embroidery with hook-and-loop backing and laser contour cutting.

Mighty Hoop 14" X1 3" (355 X 330).

Wide-area towel embroidery across the full width. The towel frame enables wide-area embroidery on towels within a defined embroidery corridor. This allows designs, logos or lettering to be positioned much more flexibly than with standard single frames. Instead of being limited to small, predefined embroidery areas, the embroidery can be positioned across the full width of the towel. This makes it easier to create wide designs, borders, names or decorative applications for hotels, wellness, sports and promotional textiles. For wide designs and flexible positioning The maximum embroidery area is 558 × 155 mm. The usable embroidery width can be flexibly adjusted from 54.5 to 155 mm, allowing it to be adapted to different towel sizes and design requirements. Suitable for ZSK machines with a large embroidery field The towel frame is suitable for ZSK flatbed machines and RACER models with an embroidery field depth of at least 700 mm. It is designed for the Z connection.

SUPPORT FOR TUBULAR ARM (HEAVY GOODS). Support to reinforce the tubular frame when embroidering heavy materials.

Tubular Hoop Support – Hoop Stabiliser for Brother PR. The tubular hoop support simply slides onto the tubular arm / bobbin arm of your Brother PR embroidery machine and provides extra stability for embroidery hoops or clamping frames. Especially when working with heavy fabrics, this original support from Mighty Hoop helps relieve undesired pressure off the arms of the machine. Even when using small or lightweight frames, the tubular hoop support minimises bouncing and vibration during embroidery, contributing to noticeably improved stitch quality. Note: Compatible with Brother PR 6 and PR 10 tubular embroidery machines. Key Benefits: Extra support for embroidery hoops and clamping frames Reduces strain on the tubular arm Prevents unwanted movement when using light frames Quick and easy to install on the tubular arm Ideal for working with heavy items

Sharply defined 3D logos in black. The Würker 3D embroidery foam in Black, density 75D, offers the same firm density as the white variant – for designs with dark thread. It suits caps and badges that need a permanently sharp, raised outline.Benefits in practiceThe 75D density holds sharp edges during stitching and produces boldly defined motifs. During stitching, the needle perforates the foam along the dense satin stitches; excess material is removed afterwards. Black combines discreetly with dark thread, without the foam becoming visible at the edges. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 75D for sharp edges and boldly defined 3D effectsBlack colour suited to designs with dark threadEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingWhite, Red, Blue, Yellow and Green are also available in the Hard variant, as well as the softer 38D range in White and Black.

Sharply defined 3D logos for corporate wear. The Würker 3D embroidery foam in Blue, density 75D, delivers sharply defined 3D logos in a colour that combines well with corporate and uniform colours. It suits designs with blue thread, for example on corporate wear, workwear or club apparel.Benefits in practiceThe 75D density holds sharp edges during stitching and produces boldly defined motifs that keep their shape even after frequent wear. During stitching, the needle perforates the foam along the dense satin stitches; excess material can be removed afterwards. The blue colour prevents a differently coloured foam from showing through at the edges when stitching with blue thread. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 75D for sharp edges and boldly defined 3D effectsBlue colour suited to designs with blue thread, e.g. corporate wearEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingOther colours in the Hard range (White, Black, Red, Yellow, Green), as well as the softer 38D range, are also available in our assortment.

Sharply defined 3D logos in green. The Würker 3D embroidery foam in Green, density 75D, suits sharply defined 3D logos with green thread, for example on outdoor or agricultural workwear.Benefits in practiceThe 75D density holds sharp edges during stitching and produces boldly defined, raised motifs. During stitching, the needle perforates the foam along the dense satin stitches; excess material can be removed afterwards. Green prevents a differently coloured foam from showing through at the edges when stitching with green thread. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 75D for sharp edges and boldly defined 3D effectsGreen colour suited to designs with green thread, e.g. outdoor workwearEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingOther colours in the Hard range (White, Black, Red, Blue, Yellow), as well as the softer 38D range, are also available in our assortment.

Bold 3D logos in red. The Würker 3D embroidery foam in Red, density 75D, produces boldly defined, raised logos in an eye-catching colour. It suits designs with red thread, for example on club and team wear.Benefits in practice75D holds sharp edges during stitching, keeping logos and lettering clearly defined. The needle perforates the foam along the dense satin stitches; excess material is simply removed afterwards. The red colour can be matched to red thread, so no differently coloured foam shows through at the edges. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 75D for sharp edges and boldly defined 3D effectsRed colour suited to designs with red thread, e.g. club and team wearEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingOther colours in the Hard range (White, Black, Blue, Yellow, Green), as well as the softer 38D range, are also available in our assortment.

Sharply defined 3D logos in white. The Würker 3D embroidery foam in White, density 75D, is the firm variant for sharply defined, raised embroidery motifs. It suits designs with light-coloured thread, for example on caps, badges or dark fabrics.Benefits in practice75D holds sharp edges during stitching, resulting in boldly defined logos and lettering. The needle perforates the foam along the dense satin stitches; excess material can be removed easily afterwards. In White, the foam suits light-coloured thread on dark fabrics particularly well, without showing through at the edges. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 75D for sharp edges and boldly defined 3D effectsWhite colour suited to designs with light-coloured thread on dark fabricsEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingBlack, Red, Blue, Yellow and Green are also available in the Hard variant, as well as the softer 38D range in White and Black.

Eye-catching 3D logos in signal yellow. The Würker 3D embroidery foam in Yellow, density 75D, produces sharply defined 3D logos in an eye-catching signal colour. It suits designs with yellow thread, for example on hi-vis or safety wear.Benefits in practice75D holds sharp edges during stitching, so logos and lettering stay clearly defined even with bold colours. The needle perforates the foam along the dense satin stitches; excess material is simply removed afterwards. Yellow can be matched to yellow thread, without a differently coloured foam becoming visible at the edges. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 75D for sharp edges and boldly defined 3D effectsYellow colour suited to designs with yellow thread, e.g. hi-vis and safety wearEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingOther colours in the Hard range (White, Black, Red, Blue, Green), as well as the softer 38D range, are also available in our assortment.

Soft 3D effects with dark contrast. The Würker 3D embroidery foam in Black, density 38D, offers the same softer density as the white variant – matched to dark or contrasting thread colours. It suits fabrics such as T-shirts or sweatshirts where the 3D effect should not feel too stiff.Benefits in practice38D processes well even on lighter fabrics while remaining comfortable to wear. Combining several layers further enhances the 3D effect. The needle perforates the foam during dense satin stitching; excess material is removed after embroidering. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 38D for softer, multi-layer 3D effectsBlack colour as a universal contrast to light-coloured threadEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingThe white variant with the same density, as well as all Hard colours, are also available in our assortment. Our team is happy to advise you.

Soft 3D effects for comfortable fabrics. The Würker 3D embroidery foam in White, density 38D, is an EVA foam for raised, three-dimensional embroidery motifs. The softer variant suits fabrics where wearing comfort matters alongside the 3D effect – for example sweatshirts or polo shirts with light-coloured thread.Benefits in practiceWith 38D, the foam stays comfortable to wear even on lighter fabrics instead of feeling stiff. For a stronger 3D effect, several layers can be combined. During stitching, the needle perforates the foam along the dense satin stitches; excess material is simply removed afterwards. As with EVA foam in general, care should take the textile, thread and foam together into account – the manufacturer's care instructions for the respective textile remain decisive.Format and hoop compatibilityThe 280 × 280 mm format covers commonly used hoop sizes up to about 10″ x 10″, such as Mighty Hoop, and can be used in many applications without prior cutting.Density 38D for softer, multi-layer 3D effectsWhite colour suited to light-coloured thread, no show-through at the edgesEVA material with a defined thickness of 3 mm for consistent results280 × 280 mm format fits common 10″ hoopsPack of 10 sheets for reliable restockingOther density grades and colours in the Würker range are also available in our assortment. Our team is happy to advise you on the right combination.